I had most of this information posted before, but the linked photos were to a personal album on the site, which was deleted in one of the upgrades. So, I decided I'd repost a new thread as I can't edit the old one to reinsert the new photos. Plus, some good information came out of the discussion in the old thread and I thought it would be good to include in the new one.
Iíve posted before about the wonders of the baking soda and aluminum foil trick for restoring tarnished silver razors, but I thought it might be helpful to have a photo tutorial. I first read of the idea in a post by AsylumGuido in a thread long buried. In more recent threads, Len (Oldguy) and T Rick wrote more about it. This thread is an attempt to distill some of the wisdom put forth by them accompanied by some photos. The material and information isnít new, but I thought a photo tutorial might be helpful. And if not, there are some good before/after photos of my new Bulldog.
DISCLAIMER: This process work greats for restoring your tarnished silver razors. But I wouldnít recommend it for razors with more ornate and intricate designs such as the American Button Company (ABC) Empire, Floral, or Scroll design. On razors with ornate designs like these, I think it looks best to only polish the intricate design that sits higher than the rest of the razor and leave the tarnish in the recessed areas. If you are trying to achieve this look, donít use this process. It will remove tarnish everywhere the water touches, which given the nature of water, is the entire razor, including the recessed portions. But if you want to remove every last little bit of tarnish, this is the process for you.
Onto the process itselfÖ
What You Will Need:
-A silver razor that is tarnished, which you want to restore. For the process to work, it needs to be a razor plated in silver. It will not work as intended on nickel plated razors. Also, it is probably a good idea to clean up the razor as much as possible with regular dish soap and scrubbing bubbles before beginning the process.
-A watertight container big enough to hold the razor and that can withstand boiling water
-A pot or pan to boil water in
The Sample Razor:
My recently acquired Gillette Bulldog from 1916. Here are some before pictures:
The Process Itself:
1) Begin by bringing the water to a boil.
You will add baking soda to the water later (once it starts boiling). But at this point, it is good to know the amount of water with which you are starting. The ratio is 1 cup of baking soda for every 1 gallon of water. This breaks down to a 1:16 ounce ratio or 1 tablespoon of baking soda to 1 cup of water.
2) While you are waiting for the water to boil:
(a) Line the container that you have chosen with aluminum foil
(b) Place the razor inside of the container that has now been lined with aluminum foil.
3) Once the water begins to boil, add in the baking soda. It may be best to do this over the sink in case it bubbles over, which is quite likely. If the water isnít boiling anymore, return it to the stove to get it boiling again. Iíve found that the hotter the water is, the more effective it will be.
4) Pour the boiling water/baking soda mix into the container. Make sure the razor is completely covered. Let it soak until the water has cooled off a bit (About 10-15 minutes).
5) Rinse the razor and check if it needs another soak. If it does, then dump out the water that has been soaking in the aluminum foil lined container, bring the water/baking soda mix back to a boil, reline the container with aluminum foil and give it another soak. Repeat until youíve achieved the desired look. Here it is after the first soak:
Here are some photos after four baths. This time around, there was quite a bit of residual gunk in the grooves that I didn't get out well enough before cleaning. Normally, it would be looking much better. But even still, it is about 80% of the way to the final product. Anyways, after four soakings:
And with just a touch of Mr. Metal polish (non-abrasive), this is the final result:
A couple people (T Rick and valmara1971) mentioned that instead of adding the baking soda to the boiling water and then pouring the mixture into the aluminum foil lined container (steps 3 and 4 above), they just put the baking soda in the aluminum foil lined container or all around the razor and then add the boiling water. If you want to try this variant, it also works. I tried this process with my recently acquired Tuckaway and it worked great. To follow this variant, start with step one. Then do 2a and 2b. Then instead of adding the baking soda to the boiling water, put it in the aluminum foil lined container that has the razor in it, like this:
Then add in the boiling water. It will bubble up significantly at first, but then settle down:
Following this process, here is a Tuckaway before and after two baths (it wasn't very tarnished to begin with and only took two) with a light polish like above:
If there is any information that you think should be added, then let me know and I'll edit the post.